update TinyUSB examples for latest TinyUSB (#325)

usb/host/host_cdc_msc_hid/tusb_config.h

@@ -30,27 +30,48 @@
  extern "C" {
 #endif
 
+//--------------------------------------------------------------------+
+// Board Specific Configuration
+//--------------------------------------------------------------------+
+
+#if CFG_TUSB_MCU == OPT_MCU_RP2040
+// change to 1 if using pico-pio-usb as host controller for raspberry rp2040
+#define CFG_TUH_RPI_PIO_USB   0
+#define BOARD_TUH_RHPORT      CFG_TUH_RPI_PIO_USB
+#endif
+
+// RHPort number used for host can be defined by board.mk, default to port 0
+#ifndef BOARD_TUH_RHPORT
+#define BOARD_TUH_RHPORT      0
+#endif
+
+// RHPort max operational speed can defined by board.mk
+#ifndef BOARD_TUH_MAX_SPEED
+#define BOARD_TUH_MAX_SPEED   OPT_MODE_DEFAULT_SPEED
+#endif
+
 //--------------------------------------------------------------------
 // COMMON CONFIGURATION
 //--------------------------------------------------------------------
 
 // defined by compiler flags for flexibility
 #ifndef CFG_TUSB_MCU
-  #error CFG_TUSB_MCU must be defined
-#endif
-
-#if CFG_TUSB_MCU == OPT_MCU_LPC43XX || CFG_TUSB_MCU == OPT_MCU_LPC18XX || CFG_TUSB_MCU == OPT_MCU_MIMXRT10XX
-  #define CFG_TUSB_RHPORT0_MODE       (OPT_MODE_HOST | OPT_MODE_HIGH_SPEED)
-#else
-  #define CFG_TUSB_RHPORT0_MODE       OPT_MODE_HOST
+#error CFG_TUSB_MCU must be defined
 #endif
 
 #ifndef CFG_TUSB_OS
-#define CFG_TUSB_OS                 OPT_OS_NONE
+#define CFG_TUSB_OS           OPT_OS_NONE
 #endif
 
-// CFG_TUSB_DEBUG is defined by compiler in DEBUG build
-// #define CFG_TUSB_DEBUG           0
+#ifndef CFG_TUSB_DEBUG
+#define CFG_TUSB_DEBUG        0
+#endif
+
+// Enable Host stack
+#define CFG_TUH_ENABLED       1
+
+// Default is max speed that hardware controller could support with on-chip PHY
+#define CFG_TUH_MAX_SPEED     BOARD_TUH_MAX_SPEED
 
 /* USB DMA on some MCUs can only access a specific SRAM region with restriction on alignment.
  * Tinyusb use follows macros to declare transferring memory so that they can be put
@@ -74,7 +95,7 @@
 // Size of buffer to hold descriptors and other data used for enumeration
 #define CFG_TUH_ENUMERATION_BUFSIZE 256
 
-#define CFG_TUH_HUB                 1
+#define CFG_TUH_HUB                 1 // number of supported hubs
 #define CFG_TUH_CDC                 1
 #define CFG_TUH_HID                 4 // typical keyboard + mouse device can have 3-4 HID interfaces
 #define CFG_TUH_MSC                 1
@@ -87,6 +108,17 @@
 #define CFG_TUH_HID_EPIN_BUFSIZE    64
 #define CFG_TUH_HID_EPOUT_BUFSIZE   64
 
+//------------- CDC -------------//
+
+// Set Line Control state on enumeration/mounted:
+// DTR ( bit 0), RTS (bit 1)
+#define CFG_TUH_CDC_LINE_CONTROL_ON_ENUM    0x03
+
+// Set Line Coding on enumeration/mounted, value for cdc_line_coding_t
+// bit rate = 115200, 1 stop bit, no parity, 8 bit data width
+#define CFG_TUH_CDC_LINE_CODING_ON_ENUM   { 115200, CDC_LINE_CONDING_STOP_BITS_1, CDC_LINE_CODING_PARITY_NONE, 8 }
+
+
 #ifdef __cplusplus
  }
 #endif